Vehicles
Sections
348 not categorized PORSCHE 944 S2 EFLCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 912 1965-69 (includes uncategorized and accessory items) FVD362041002 High quality wheel nut and lock set. The set includes a key and teflon insert for your lug tool so the nuts will not be marred when removed. Please check the exact model designation for this part below. Sold as a set. 1 necessary per car.
$35.20
Make a selection 150SPB965 Replace the worn-out spring plate bushing with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is the inner bushing for the 1-piece non-adjustable spring plate. Sold individually. 2 necessary per car.
$47.30
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection BL911 Over the years, deposits form inside your rubber brake lines, creating a hard brake pedal and sticky calipers. The permanent cure is to install a set of our stainless brake lines. They are teflon-lined to prevent mineral buildup and braided stainless steel to reduce line flex! (sold in sets of four.) excellent brake hose for racing. General Fitment912 1965-69911 1965-69
$75.59
Make a selection 96437504381 Replace your worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushing. This is manufactured of rubber with a 75-shore hardness value. 75-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings rubber has a shore hardness value of 75 (like rs models) made in Germany this mount is a high-quality OEM (original equipment manufacturer) replacement part, designed to perform like t...(choose a part on the right to read more)
From $199.99
Make a selection 150TBR900 Replace worn-out original front control arm / wishbone bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is located at the front of the control arm / wishbone. The correct matching poly-graphite bushing for the front of the control arm is part # 150tbf900 sold individually. 2 necessary per car.
$49.50
Make a selection 911FDLNK Upgrade your stock front swaybar with this simple bolt in replacement for the factory drop links.
$205.00
Make a selection 150SC030 Protect your valuable dashboard and interior the next time you take your car out! Our sun shades are tailor fitted for your Porsche! Features: laminate construction for durability. Silver reflective surface. Foam core for insulation. Folds easily for storage.
$109.99
Make a selection 150PB1027 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's 911 models from 1978-89 if fitted with an 18mm original rear sway bar.
$49.50
Make a selection 150PB100922 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection 95037003 Stoptech brake lines consist of a ptfe (commonly referred to as teflon) inner line that carries the brake fluid, which is then covered with a layer of stainless steel woven braid. The ptfe tube is very resistant to expansion under pressure and will not degrade from exposure to brake fluid. every stoptech brake line is 100% tested in-house to a pressure of 4,500 psi. This is almost 4 times the typical line pressure exerted by a production vehicle's master cylinder. stoptech is a registered brake line manufacturer with the united states DOT and all stoptech stainless steel brake lines are manufactured to meet DOT compliance standards. Stoptech stainless steel lines also meet or exceed fmvss 106 and applicable...(choose a part on the right to read more) General Fitment911 1965-69911 1970-73 911 1974-77 911 1978-83 911 1984-86 912 1965-69
$91.60
Make a selection 150PB100918 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection 150PB100916 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection COVER Our custom-fit car covers fit your Porsche like a glove! Car covers are an excellent and inexpensive way to preserve your Porsche. The "noah" fabric actually stops water, yet it “breathes” to allow any trapped moisture, seam seepage or condensation to easily evaporate. Highly water resistant, uv resistant and breathable. Made in the us. When ordering, please indicate your year, make, model, number of side mirrors, regular or turbo or turbo-look body style, with or without whaletail spoiler, and which type cover you would like. These covers are made to order and may take longer to ship. When ordering, make sure you indicate year, model, body style, number of exterior side mirror, and with or without rear s...(choose a part on the right to read more) General FitmentALL
$299.00
Make a selection 90150504651
View/Change Diagram
From $137.50
Make a selection 91156400501 Known as: air deflector / air deflector without / air deflector with spoiler f 91ks1 20767>>
$157.78
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |